Home Privacy Policy | Contact Us | Return Policy


 

SUNUS, LEVELUK R, K8, Leveluk DXII, Leveluk JRII, Leveluk SD501, SD501 Platinum, SUPER501, Leveluk SD501U.

 

Water Filtration Products

Kangen Water Research
Alkaline Health Books

Kangen Water Videos

Compatible Kangen Water Replacement Filters

HIGH Performance Filter
HIGH Performance HGN
PREMIUM Performance Filter
PREMIUM Performance HGN

ULTRA Performance Filter
ULTRA Performance HGN
UltraPremium Kangen Filter 
UltraPremium Kangen HGN Filter

Reusable Cleaning Cartridge

One Time Use HGN Cleaning Cart.
One Time Use Cleaning Cart.

REUSABLE Cleaning Cartridge
REUSABLE Cleaning HGN Cartridge Crystaline Cleaning Granules

Pre-filters & Housings

Faucet
Diverters & Hoses

 

Shower Filters

Rainshower Shower Filter
Crystal Quest Shower Filter

Bath & Pool Filtration

Crystal Bath Ball Filter and Replacement Pouch

Whole House Filters

 

Singflo Water Pump

Testing Kits & Meters


Alkaline Water Test Kit
WaterSafe Test Kit
Fluoride/Chlorine Test Kit
pHydrion pH Test Paper

Health Books


Reverse Aging
Alkalize or Die

Powerful Magnets


Hard Water Magnetizer

watersafe® Water Test     
For city or municipal source water

Watersafe® Pesticide Test Kit Instructions

The Watersafe Pesticide test kit is a one step test kit that detects two of the most common pesticides (Atrazine - 3 ppb and Simazine - 4 ppb) used in the United States at the EPA maximum contaminant level. Results in 10 minutes. If you car concerned about  pesticides on your produce, then you should be also concerned about pesticides in your drinking water? Now you can test your water for harmful pesticide contamination-safely and accurately.

Before you begin

  1. Keep tests out of reach of children and pets.

  2. Do not ingest anything from this test kit. Do not drink water sample used for testing. Store and use at room temperature (60-86 F).

  3. Do not open packets or a vial until you are ready to perform the tests.

  4. Do not use on hot water or water containing bleach detergents.

  5. Do not re-use any part of the test kit.

  6. Read and follow all instructions carefully.

Pesticide Test Instructions

  1. Open Pesticide packet and take out all contents. The packet contains a test vial, a dropper pipette, two Watersafe® test strips, and a desiccant (to be discarded).

  2. Using the dropper, place exactly TWO dropper-fuls of water sample into test vial. To pick up the sample, tightly squeeze the bulb at the end of the dropper and place the open end into the water sample. Release the bulb to pick up the sample, then squeeze again to expel the sample into the vial.

  3. Swirl vial gently for several seconds. Place on a flat surface.

  4. Place both test strips into the test vial, with arrows pointing DOWN

  5. Wait 10 minutes. Do not disturb strips or vial during this time. Blue lines will appear on the strips.

  6. Take the strips out of the vial and lay them on a flat surface with the arrows pointing to the LEFT.

Interpreting The Results:

Negative: If the LEFT line (next to number 1) is darker than the RIGHT line (next to number 2) or if you only see the LEFT line (next to number 1), the test is negative)



Positive: If ihe RIGHT line (next to number 2) is darker than the LEFT line (next to number 1), or if lines are equally dark (Both LEFT and RIGHT lines are equally dark)

7. Note: If no lines appear, or both lines are very light, the test did not run properly and the result is not valid. If a test strip shows a positive result, your water sample may contain lead or pesticides at a toxic level.

[Watersafe City Water Test Kit Page] [Watersafe Well Water Test Kit Page]

[Water Test Kit Page